PS2 RGB...If you've done it please come here!
Moderator:Moderators
- segasonicfan
- Moderator
- Posts:516
- Joined:Fri Jul 23, 2004 3:57 am
I just have a simple question about hooking up the PS2 to an RGB monitor (i.e. PSOne screen). Do you need 220uf caps inbetween the RGB lines or 75 ohm resistor to ground? Or can you just connect all the RGB lines directly?
The reason why I ask is because I've connected all the lines directly but after about 30 min into my games I get a greenish tint to the screen. I'm also using the Y output as Sync which is also highly possible to be the cause of this problem. I believe I need an LM1881 to strip the sync from composite.
Please tell me how you hooked up your RGB PS2. Thanks!
-Segasonicfan
Gamelver here. check page two for a quick fix to the green tint problem . Thanks segasonicfan for figuring it out! Now then, back to Sonic and Knuckles....
The reason why I ask is because I've connected all the lines directly but after about 30 min into my games I get a greenish tint to the screen. I'm also using the Y output as Sync which is also highly possible to be the cause of this problem. I believe I need an LM1881 to strip the sync from composite.
Please tell me how you hooked up your RGB PS2. Thanks!
-Segasonicfan
Gamelver here. check page two for a quick fix to the green tint problem . Thanks segasonicfan for figuring it out! Now then, back to Sonic and Knuckles....
-
- Posts:1056
- Joined:Tue Jun 14, 2005 11:19 am
- Location:New Orleans, LA
- Contact:
I forget how I got rid of that problem. something about shorting two pins together on the connector (it was on the old www.konlabs.com site, but now it's gone)
was it just +5v to gnd....?
I'm making this up as I go, it was years ago
was it just +5v to gnd....?
I'm making this up as I go, it was years ago
- segasonicfan
- Moderator
- Posts:516
- Joined:Fri Jul 23, 2004 3:57 am
LOL, it definitely isn't 5v to ground...that'll kill your video chip x_X
I just tried stripping the sync from composite (thinking the Y output was the problem) but I still got the tint....dammit. :/ Any other ideas? It's strange because I got flamed in the RGB forums on GameSX for saying all PSTwos have the green tint problem...everyone else swore it didn't (?) see here:
http://nfg.2y.net/forum/index.php?showtopic=1551
-Segasonicfan
I just tried stripping the sync from composite (thinking the Y output was the problem) but I still got the tint....dammit. :/ Any other ideas? It's strange because I got flamed in the RGB forums on GameSX for saying all PSTwos have the green tint problem...everyone else swore it didn't (?) see here:
http://nfg.2y.net/forum/index.php?showtopic=1551
-Segasonicfan
-
- Posts:1056
- Joined:Tue Jun 14, 2005 11:19 am
- Location:New Orleans, LA
- Contact:
I think it's really be the monitor with a green tint problem, since my GBA setup had it too. just to be clear, we're both talking about the psone monitor, correct?
I've been banging my head for a couple days trying to think of the fix, but in reality I never new it, and just blindly looked it up on the now nonexistant konlabs site. (yes, I thought I hooked something up wrong at first too)
I hate to suggest it, but ben may know. His NeoGeo portable uses the RGB on the Psone monitor. Or maybe it's only certain psone screens that experience this issue.
It could be as simple as sending a pulse down the pins that switch on the monitor power every so often. I don't even really remember how that worked.
I've been banging my head for a couple days trying to think of the fix, but in reality I never new it, and just blindly looked it up on the now nonexistant konlabs site. (yes, I thought I hooked something up wrong at first too)
I hate to suggest it, but ben may know. His NeoGeo portable uses the RGB on the Psone monitor. Or maybe it's only certain psone screens that experience this issue.
It could be as simple as sending a pulse down the pins that switch on the monitor power every so often. I don't even really remember how that worked.
- segasonicfan
- Moderator
- Posts:516
- Joined:Fri Jul 23, 2004 3:57 am
az--yea I know we're not talking about that. There's actually a green tint problem that shows up later even if you select RGB output in the menu.
I know switching to composite and back to RGB never worked to fix it and I don't think turning the screen on and off ever worked either... :/
I just don't see how it could be a problem with the PSOne screen since it works flawlessly with other RGB systems. I think it has to do with the PS2 swapping from Component to RGB digitally and using the same outputs. It must leave some trace of 'sync on green.' That's why I was hoping stripping the sync information from composite would solve the problem...but it looks like the problem is actually in the RGB lines themselves. That doesn't make a whole lot of sense though because R-Y and B-Y (the analog version of Pb Pr) stands for red minus luminance and blue minus luminance. If you connect them to a monitor you don't get any green signal mixed in b/c even in component it's not there. The green is mixed with Y.
So in conclusion the problem is with the green output (somehow).
-Segasonicfan
I know switching to composite and back to RGB never worked to fix it and I don't think turning the screen on and off ever worked either... :/
I just don't see how it could be a problem with the PSOne screen since it works flawlessly with other RGB systems. I think it has to do with the PS2 swapping from Component to RGB digitally and using the same outputs. It must leave some trace of 'sync on green.' That's why I was hoping stripping the sync information from composite would solve the problem...but it looks like the problem is actually in the RGB lines themselves. That doesn't make a whole lot of sense though because R-Y and B-Y (the analog version of Pb Pr) stands for red minus luminance and blue minus luminance. If you connect them to a monitor you don't get any green signal mixed in b/c even in component it's not there. The green is mixed with Y.
So in conclusion the problem is with the green output (somehow).
-Segasonicfan
Hey Segasonicfan. I used your guide to making a ps2p and I am using a PSOne screen, and im not having any problems with green tint showing up after some game play time. I'll see about making a graphic of what i connected... I'm fairly sure I did it right(the screen hasnt blown up yet, and i've logged about 50 hours on RE Outbreak File:2 )
Why make a portable? Because I want to be able to game cordless.
and here's my PS2p !!
ttp://i27.photobucket.com/albums/c180/th3c4rd/b645741d.jpg
and here's my PS2p !!
ttp://i27.photobucket.com/albums/c180/th3c4rd/b645741d.jpg
- segasonicfan
- Moderator
- Posts:516
- Joined:Fri Jul 23, 2004 3:57 am
- segasonicfan
- Moderator
- Posts:516
- Joined:Fri Jul 23, 2004 3:57 am
Does anyone have an update on this? This has really been bothering the hell out of me. I've been working on an insanely hard Component -> RGB converter which will hopefully solve the problem but I wonder if someone has a similar solution (Ben??) This is sort of the final frontier for my PS2 portable to be perfect (I'm upgrading it right now and while it's opened up I'd like to fix this). I have also discovered a better solution for the power supply if anyone's interested...
But about the video problem, I really want to get this fixed without the encoder. I will seriously pay someone to tell me if I have to lol.
-Segasonicfan
But about the video problem, I really want to get this fixed without the encoder. I will seriously pay someone to tell me if I have to lol.
-Segasonicfan
- Turbo Tax 1.0
- Portablizer Extraordinaire
- Posts:4773
- Joined:Wed Mar 30, 2005 6:19 pm
- Location:Delaware, no sales tax
- Contact:
- segasonicfan
- Moderator
- Posts:516
- Joined:Fri Jul 23, 2004 3:57 am
- XPCportables
- Posts:1020
- Joined:Mon Aug 08, 2005 3:27 pm
- Location:The end of time...